Frequently Asked Questions

FAQ

How to remodel a bathroom that is in the cnter of the house

Oct 13, 2022 — 12 DIY Bathroom Renovations To Boost Your Home's Value · 1. Add a Bathroom · 2. Install Walk-in Shower · 3. Change the Vanity · 4. Add Mirrors · 5.

Is it difficult to relocate a shower?

Toilets, sinks, and showers will always require pipes that wind through the house to connect to vent, water, and drain lines. The farther away you move these fixtures from those lines, the more complicated it gets and the longer it will take.

Can you reposition the shower?

If you plan to place your shower in another part of your bathroom, keep in mind that you will need to move the drain too. The shower drain helps prevent water from backing up into your bathroom and causing extensive damage, so it's important to ensure that you installed a new drain correctly.

How hard is it to rearrange the plumbing in a bathroom?

While moving the plumbing is the most challenging part of the bathroom remodel, it's possible. The trick is to create an access panel to the pipes. If you don't have an access panel, you can create one from an adjoining room or sidewall. The best solution for this is to install an access panel in your closet.

What is the hardest part of renovating a bathroom?

Bathroom Remodel Demolition

Perhaps the most physically difficult aspect of a remodel is demolition.

Is it expensive to move a bathroom?

As we can see, the cost of relocating a bathroom can be high. Still, those prices rely on whether you want to rip out and dispose of an old bathroom entirely or whether the project involves repositioning the same units. The good news is that moving a bathroom upstairs can provide an instant return on your investment.

What is the most expensive part of a bathroom remodel?

When it comes to remodeling, the highest single cost is labor, which usually accounts for 20%–65% of the final cost. However, if you're looking at the tangible items within a bathroom, the wet area (tub, shower, and wall surrounds) is the most expensive part.

How do I know if I have a 10 or 12 inch rough-in toilet?

The standard rough-in dimensions for toilets is 12-inches. A distance of 10-inches or 14-inches is occasionally found in small bathrooms or older homes. Determine your bathroom's rough-in by measuring from the wall behind the toilet to the middle of the bolts on the base of the toilet.

What's the typical rough-in for a bathroom toilet?

12 inches

What is a rough-in size for a toilet? A toilet's rough-in size measures the distance from the back wall to the center of the drainpipe, otherwise called the toilet flange. This rough-in measurement usually comes in at 12 inches, but some bathrooms and toilets require 10-inch or 14-inch rough-in distances.

What is the plumbing rough-in for a toilet?

12 inches

The standard rough-in size for a toilet is 12 inches in contemporary houses and 10 inches in older homes. These are the toilet rough-in dimensions: Supply line (vertical): 8 1/4 inches of height to accommodate most base moldings.

Can I replace a 14 inch rough-in toilet with a 12 inch rough-in toilet?

Probably. You can get offset adapter flanges and replace the flange with one that scoots over a couple of inches. Or, you can mount the 12″ toilet where the 14″ was and it will sit 2″ further from the wall. If you want to hide that you can put a small shelf over the toilet.

Can you replace a 12 inch rough-in toilet with a 10 inch rough-in toilet?

While a 10-inch rough-in toilet can plausibly fit into a 12-inch rough-in (though a longer connector may be needed), the same cannot be said for using a 12-inch rough-in toilet in a 10-inch rough-in. A 12” rough-in toilet will not fit in a bathroom with a 10” rough-in size.

In what order do you do a bathroom renovation?

What Order To Do Your Bathroom Renovations

1. Deciding what to change.
2. Outlining your budget.
3. Choosing the right design. Colour scheme. Sanitary ware. Wall and floor covering. Lighting. Fitted furniture. Heating and ventilation.
4. Demolishing the old bathroom.
5. Installing a new bathroom.

Should you install tub before or after tile?

With placing the bathtub before the flooring and wall, you can better position the bathtub for protection and aesthetics. Without having to worry about damaging the flooring and wall, you can simply place the bathtub where you want and place the flooring and wall after to limit gaps between the two.

Do you install drywall or tub first?

You put the drywall in after the tub is installed. I like to treat the walls with liquid silicone and then install the tiles. I won't go into tile insulation but fill the tub with water before you start the first row of tile .

How long does a bathtub installation take?

In general, the usual maximum amount of time a bathtub remodel will take is up to two weeks. This length of time is usually for difficult bathtub remodels with complex tiling. However, most companies like Bath Solutions can install your bathtub in only one day.

Do you put flooring under bathtub?

Protect against floor scratches, cracks, stains and damage

If the flooring is placed before the bathtub, it can lead to scratching or damaging the floor with trying to position a heavy object like a bathtub, so you can simply place it first and add the flooring and walling to make it more convenient.

Do you install flooring before bathtub?

If the flooring is placed before the bathtub, it can lead to scratching or damaging the floor with trying to position a heavy object like a bathtub, so you can simply place it first and add the flooring and walling to make it more convenient.

When should a bathtub be replaced?

The average bath needs replacement every 10 to 30 years, with porcelain-enamel products offering the longest lifespan. Towards the end of that period, gaps and cracks will appear, ultimately leading to leaks. Water is one of nature's most destructive elements, so even a subtle leak needs immediate attention.

Should you install toilet before or after tile?

Decisions about the toilet

The toilet flange then goes atop after you install tiles for the bathroom flooring. Unless you are in a situation where it is impossible to redo the floor tile due to the flange already being put in, never put the tiles below the existing toilet and the flange.

In what order do you install a bathroom?

Steps in the Bathroom Installation Process

1. Step 1: Bathroom Layout Plan.
2. Step 2: Install Sanitary Piping and Plumbing Lines.
3. Step 3: Install Electrical Wiring.
4. Step 4: Fix the Countertop and Install the Bathtub and Shower Enclosure.
5. Step 5: Fix the Wall Tiles and Flooring.
6. Step 6: Paint the Walls and Ceiling.

What to consider when remodeling a bathroom

What should I install first in my bathroom?	If you are undertaking a complete bathroom renovation, it's generally best to start with the plumbing. This will give your plumber plenty of space to work, and it will also make it easier to tile the bathroom once the plumbing is in place.
What to do before tiling a bathroom?	Firstly there are some basics steps to take before tiling a wall including: Removing any screws/photo hooks/nails or other fittings. Remove any loose plaster. Remove old wallpaper. Fill any large cracks/holes in the wall. Ensure the wall is level and sand if required. Remove any dust with a vacuum and wipe clean the walls.
Do you tile a bathroom wall first or last?	Whilst you can tile either one first, popular opinion based on experience is that is is easier to tile the walls first and then the floor, if you are tiling both in a room. This ensures that you keep the floor tiles cleaner as you won't be doing so much work around them once they are installed.
When renovating a bathroom do you tile first?	Why You Should Tile the Floor First. The tile installation principle is that the tiled wall 'hangs' over the tiled floor. The best way to achieve this outcome is by first tiling the floor so that the wall tile will then seem to be 'sitting' on the bathroom floor.
What order do you install a new bathroom?	How to Remodel a Bathroom in 7 Steps Remove Bathroom Fixtures. Install the New Shower or Tub. Lay the New Flooring. Hang Drywall and Start Painting. Install Cabinets and Vanity. Update Lighting. Hook Up the Plumbing.
How to totally remodel a bathroom that is in the center of the house	Jun 26, 2021 — Bring everything down to studs and subfloor, then resheetrock, install your fixtures, tile, paint, and call it a day! I make it sound way to easy. I'm mid-way
How do you renovate walls?	The customary way to upgrade a wall in an old house is to tear off the old materials out to the wall studs (collect the treasures hidden in there) insulate, rewire and add new wallboard, plaster, or another interior finish.
In what order should you remodel your home?	Home Renovation Timeline Week 1 – site preparation and demolition. Week 2 -3 – rough work. Week 4 – drywalling and finishes. Week 5 – interior trim and cabinetry. Week 6 – painting. Week 7 – trim out from trades, lighting, and fixtures. Week 8 – flooring, final finishes, and cleaning. Scope of work.
What to do first when remodeling a room?	Practically speaking, you'll want to do the kitchen remodel first because that work will create the most dust and debris, which you won't want to land on new paint or finish jobs. It's always a good idea to isolate any demolition mess by putting plastic over doorways or pass-throughs.
What do I need to know before remodeling?	To set yourself up for a smooth, stress-free project, make sure to consider the following factors before your next remodeling project. Design Inspiration. Space and Square Footage. Budget. ROI and Neighborhood Comps. Building Permits. DIY vs. Hiring Your Contractor. Schedule and Quality of Life.
How do you prepare old walls?	How to prepare a room for painting Make space. Remove as much of your furniture as you can. Inspect your walls for any damage. Start by inspecting your walls carefully. If there is damage, repair it. Sand. Clean your walls. Let the walls dry. Clean up any mess. You're ready to paint!
How hard is it to reroute plumbing?	This can get challenging, as pipes are often embedded in wall spaces or covered by other surfaces and materials. The easiest option is to run piping through paths that have already been designed for plumbing, as they are designed to handle long piping tubes.
How do you permanently cap off a water pipe?	How to permanently cap off a water pipe? To begin with, you need to wipe the endings of the pipe first. Apply PVC cement into the cap socket and try to place the pipe horizontally and keep the cap on top. Last but not least after finishing you should check if there is any water coming from the PVC pipe.
How do I turn off the water in my bathroom renovation?	Toilets: A single shutoff valve (a toilet uses only cold water) is usually located near the floor below the water supply valve on the bottom left side of the toilet tank. Showers/tubs: Look around the tub or shower for an access panel. It may be on the other side of the wall from the tub or shower.
How do you cover exposed plumbing pipes?	How to Hide Exterior Plumbing Pipes Use Plants. One of the most popular ways to disguise exposed exterior pipes is to use plants. Use a Wooden Box. A wooden box is a great option for pipes grouped together. Use Decorative Objects. Paint the Pipe. Cover the Pipe. Industrialize the Pipe. Now You Know.
Can you reroute plumbing in a slab foundation?	Many plumbing service providers may choose to reroute existing pipes that are located in a slab. Rerouting them, outside along walls or through walls or ceilings.
Should I keep the tub in a bathroom remodel?	If you have small children and/or a dog and you don't have another tub in your home, it's wise to include one in your renovation. If only you or you and your partner will be using the main bathroom and you don't really take baths, a walk-in shower can be the perfect choice.
How to remodel a bathroom tile?	You can also check out our post on how to measure out your square footage! Remove the Old Tiles. Clean & Prepare the Surface. Prepare Underlayment & Attach Backer Board. Determine Your Tile Layout. Install New Tiles. Add Grout Between the Tiles & Caulk.
How can I renovate my bathroom without removing tiles?	5 IDEAS TO RENOVATE YOUR BATHROOM WITHOUT REMOVING TILES Install a shower enclosure without drilling. A new toilet cover to change everything. Add bathroom faucets without masonry work. Bathroom accessories without drilling the wall.
How can I redo my bathroom for cheap?	Tips To Tackle a Bathroom Makeover on a Budget Tip 1: Start with a plan. Tip 2: Keep the existing layout. Tip 3: Reuse as many existing materials as possible. Tip 4: Update as much as you can with paint. Tip 5: Update an outdated floor tile. Tip 6: Consider tiling over existing tile.
How much does it cost to retile a bathroom?	It typically costs between $450 and $10,000 to retile a bathroom, with an average of $2,000 including labor. Licensed General Contractor, Architexture Home Center, Inc.

• Should shower floor be lighter or darker than walls?

  • As a general rule of thumb, it is best for a bathroom floor to be a darker shade than the accompanying walls and ceiling. However, if your personal preference dictates, you can choose to be adventurous and go against the grain in this regard.

• Should bathroom floors match the rest of the house?

  • Typically, homeowners opt for the same flooring throughout their homes because it creates a cohesive, seamless look. However, some homeowners prefer to mix and match flooring to create a more unique and functional design for their space. There are pros and cons to both options.

• Can you use any floor tile in a shower?
  • Stone and porcelain tiles are the best for the shower floor. Avoid glazed ceramic tiles in this spot, as they tend to be slippery. Also, remember that non-vitreous tiles are not suitable for the shower floor. Only impervious or vitreous tiles should be used in the shower area, as they are relatively more waterproof.

• Can you have different tiles in bathroom?

  • If you're mixing and matching tiles, choose no more than three different types of tiles. If you choose more tile types, you'll unnecessarily make your bathroom look busy. Consider tiles for your shower space and make sure that they complement the rest of your bathroom.

• What color is best for shower tile floor?

  • White Tile

    Use Classic White Tile

    Simple and clean white tile is always a great pick for your walk-in shower. It works especially well in smaller showers and bathrooms, as the white brightens up the space and makes it feel larger in the process.

• How much value does a half bathroom add to a house?

  • Around 10%

    In general, a half bath can raise your home's value by around 10% at the highest, depending on the style and quality of your bathroom. This percentage can fluctuate between 5-10% depending on the area you live in and the market, but half baths are seen as valuable additions and worthwhile investments.

• Should all bathrooms in a house match?
  • There's no rule that every bathroom in your home has to be the same color or be decorated in the same style. However, if you like a similar style throughout, it's probably a classic style that will be beautiful in any bathroom.

• What is the cheapest way to add a bathroom to a house?

  • If you're looking to put in a new bathroom on a budget, try these tips: Convert rather than build. “Opt for an existing space that can be remodeled into a bathroom as it's a much more affordable option than building a new space,” Graham advises. Use existing plumbing and electrical where you can.

• How do you shower when bathroom is being renovated?
  • Where do you have a shower if your bathroom is getting renovated?
    1. Use your other bathroom.
    2. Attach a portable shower head to the laundry tap.
    3. Use an outdoor shower connected to the hose tap.
    4. Get a plumber to set up a temporary shower.
    5. Hire a motorhome with a shower and park it outside.
• Do shower pipes need to be replaced?

  • Depending on the material, you'll probably need to replace your pipes somewhere between 20 and 100 years after their initial installation. The longest-lasting materials are cast iron and copper, with a lifespan of 50 to 100 years, whereas galvanized steel and brass pipes can last up to 50 years.

• Can shower plumbing be moved?
  • When moving a shower, you will run into all sorts of additional steps that have to be taken, including moving the shower drain and moving shower plumbing to another wall. However, the benefit of all this work is a completed bathroom aesthetic that is perfectly customized to the client.

• Does remodeling a shower increase home value?
  • Remodeling your bathroom can be a great way to increase your home's market value and desirability to potential buyers. In fact, a full remodel may not even be necessary to see a strong return on your investment: Updating to a glass shower alone can add tremendous value and can help you to sell your home more quickly.

• Should you install flooring or bathtub first?

  • Protect against floor scratches, cracks, stains and damage

    If the flooring is placed before the bathtub, it can lead to scratching or damaging the floor with trying to position a heavy object like a bathtub, so you can simply place it first and add the flooring and walling to make it more convenient.

• Should you tile before or after fitting bath?
  • We recommend having your tiles fitted before installing a sink, shower, bath and toilet. This means your bathroom suite can sit on top of the tiles, providing a better seal and finish.

• What is the rule of thumb for bathroom remodel?

  • Rule 1: Budget based on home value

    Consumer Reports gives a good rule of thumb for total remodeling cost: it should based on 5%-10% of your home's value. So, if your home is worth $200,000, then the remodel will probably cost about $10,000 to $20,000.

• Should vanity go in before or after flooring?

  • Generally, flooring contractors prefer that the cabinets go in first so that there is less possibility of the floor getting scratched. Cabinet installers like the floor to be in place so that the cutting and dust from the floor installation will not damage the vanity.

• How much profit should a contractor make from a bathroom remodel?

  • The average gross profit margin for the remodeling industry is 17.62%, and the industry average for home builders is 19%-20%, according to Chron.com. However, this profit margin can vary based on several factors, such as material costs, labor costs, marketing, and competition.

• How many days does it take to remodel a shower?

  • However, if there are other things you want to be done, like re-tiling or installing another handheld showerhead, then expect the process to last longer. Conversely, if you undertake a budget shower remodel, then it'll take around 23 days to complete this project.

• How do I interview a contractor for a bathroom remodel?
  • Questions about a Contractor for a Bathroom Remodel
    1. How long have you been a bathroom professional?
    2. Were you formally trained?
    3. How did you acquire your experience?
    4. Do you belong to any professional associations?
    5. Are you licensed and registered with the state?
    6. Are you insured?
    7. Do you have any references I may contact?
• How much should contractors mark up materials?

  • 7% to 20%

    As a general contractor, this is your profit margin, or in other words, the amount left over after paying all of the costs of the job. A typical contractor markup is usually calculated by percentage, with the average markup varying from 7% to 20% or more.