What Are the Temporary Services Needed on a Construction Site?

When embarking on a construction project, it is essential to understand the temporary services required to ensure smooth operations and compliance with safety regulations. This guide aims to provide a comprehensive overview of the temporary services needed on a construction site, their benefits, and the conditions in which they are used.

I. Temporary Power Supply:

  • A reliable power supply is crucial for running construction equipment and tools.
  • Temporary power services provide electrical connections for lighting, machinery, and other equipment.
  • Benefits:

    1. Enables uninterrupted work progress.
    2. Reduces the risk of accidents caused by inadequate lighting or faulty equipment.
    3. Increases productivity and efficiency.

II. Temporary Water Supply:

  • Construction sites often require a temporary water supply for various purposes.
  • These services ensure a sufficient and clean water source for construction activities.
  • Benefits:

    1. Facilitates dust control, concrete mixing, and equipment cleaning.
    2. Ensures a safe environment for workers' hydration and sanitation needs.
    3. Minimizes disruptions caused by water scarcity or contamination.

III. Temporary Sanitation Facilities:

  • Construction sites must provide adequate sanitation facilities for workers.
  • Temporary services offer portable toilets

Construction site generators will require no less than 7500 running watts, however, it is always best to buy a generator that produces more power than this for your construction site.

What size generator will run a 200 amp service?

A generator in the 27-36kW range is perfect for most homes since they replace 75% of the 200 amps coming into your electrical panel.

What size generator do I need for a commercial building?


Retail application50 kilowatts + 10 watts per square foot
Other commercial applications50 kilowatts + 5 watts per square foot.

How big of a generator can I run on a 30 amp breaker?


Overall, you should be fine with a 3,000W generator, or a 3,500W one on the safe side. Since the system is limited to 3,600W, buying a 4,000W generator may get everything you can out of your system, but you're wasting 400W and burning fuel that you don't need to.

How many watts is a jobsite generator?

For simple jobs, you may only need a medium generator. These typically put out 3,000 to 5,000 watts, and are capable of handling several different hand tools. Large units are best if you have tools that utilize more watts or if you need to power more than one tool.

What are the temporary works in the construction industry?

What are temporary works? Temporary works (TW) are the parts of a construction project that are needed to enable the permanent works to be built. Usually the TW are removed after use - eg access scaffolds, props, shoring, excavation support, falsework and formwork, etc.

What is an example of temporary construction?

Temporary works often include structures, such as excavation support systems, underpinning, scaffolds, bracing and shoring, formwork, falsework, work platforms, decking, roof protection and structures used in on-site contractor facilities.

Frequently Asked Questions

What are common temporary works?

Examples of temporary works include:
  • Hoarding.
  • Scaffolding.
  • Propping.
  • Shoring and excavation support.
  • Falsework and formwork.
  • Cranes bases.
  • Signs.
  • Anchors.

What are five steps for electrical safety?

5 tips for electrical safety
  • 1 Avoid contact with power lines. Stay at least 10 feet from overhead lines, or de-energize or guard lines when working near them.
  • 2 Ground electrical equipment.
  • 3 Take care with power tools.
  • 4 Wear protective clothing.
  • 5 Stay on top of housekeeping.

What must be provided at construction sites to guard against electrical shock?

6 ways to keep workers safe from electrical hazards
  • Insulated gloves: Properly rated voltage-level gloves can help protect workers from electrical shock and burns.
  • Safety glasses: Safety glasses protect your eyes from flying debris, sparks, and other hazards while working on electrical systems.

What is Section 186.007 of the Texas utilities Code?

186.007. PUBLIC UTILITY COMMISSION WEATHER EMERGENCY PREPAREDNESS REPORTS. (a) In this section, "commission" means the Public Utility Commission of Texas. (4) make recommendations on improving emergency operations plans and procedures in order to ensure the continuity of electric service.

What is the purpose of the Texas Electric Utility Code of Conduct?

These rules govern how regulated energy delivery companies operating in Texas should interact with their competitive affiliates in order to create and maintain an open and fair competitive market and to ensure that regulated utilities do not favor their own competitive affiliates over other market participants.

Who regulates electric utilities in Texas?

The Public Utility Commission of Texas (PUCT) regulates the state's electric, telecommunication, and water and sewer utilities, implements respective legislation, and offers customer assistance in resolving consumer complaints.

What is Section 141.010 Texas Utilities Code?

(b) If a person proposes to sell or convey real property located in a propane gas system service area owned by a distribution system retailer, the person must give to the purchaser written notice as prescribed by this subsection.

What are the OSHA safety tips for electrical connections?

Stay at least 10 feet away from overhead power lines and assume they are energized. De-energize and ground lines when working near them. Use non-conductive wood or fiberglass ladders when working near power lines. Worn cords can expose the wires within, or loosen the connections on the plug end.

What is a temporary facility in construction?

When you are planning a construction project, you are going to need to provide some temporary facilities. E.g. a site office, toilets, and other welfare facilities. Used correctly, these facilities will keep your site safe and productive.

What should be in a site office?

You must include several pieces of paperwork and documentation within your site office; these include:
  • Accident log.
  • First aid kit.
  • Fire extinguisher.
  • Induction forms.
  • Health and Safety Policies.
  • Construction schedules/plans.
  • Risk assessments.
  • Contracts.

What are the construction facilities?

Definition. Facilities that are constructed, rented, renovated, etc., strictly for use during the construction phase of the project (e.g., structures, roads, utility connections, parking, walkways).

What is the construction of a temporary structure required to support?

Shoring: The process of construction of temporary structures to support unsafe structures temporarily.


How do you power a construction site?

In order to provide all the needed power at a construction site, general contractors often use large, often transportable power supplies, like generators, temporary solar panel installations and even the existing municipal power grid.

How do I calculate generator requirements?
Steps for Estimating Starting and Running Wattage
  1. Select the items you wish to power at the same time, and add together for the total running watts.
  2. Selected the item with the highest number of starting watts.
  3. Add the two numbers together for total watts needed.
What size generator do I need for 2000 square feet?

The watts consumption of a 2000 sq. ft. house will depend on the usage and number of appliances, like microwaves, TVs, refrigerators, and air conditioners. While an average household consumes around 5-7kWh, you might need a solar generator of 12-15kWh to power heavy-duty devices.

Can you run a jackhammer off a generator?

In comparison, your average solar generator has a power output of about 1000 - 2000 watts. This means that in theory a solar generator can provide enough power to operate a jackhammer. However, to power a jackhammer, you will need a solar generator with a high enough power output to meet the tool's power requirements.

How far does a ground rod need to be from a temporary power pole?

The ground rod must be located no less than 12 inches from the pole surface.

What size wire do I need for a temporary pole?

Customer provides and installs service entrance wires, size #6 copper or #4 aluminum, minimum. A minimum of 3' of each conductor shall extend beyond the weatherhead. All wires should be same size. (NEC) 6.

What are the requirements for a temporary power pole in California?

The minimum size of a temporary wood pole shall be 6 inches by 6 inches (nominal) if square, or have a top diameter of at least 5 inches if round, and be of sufficient length to maintain all required overhead clearances specified in Section 2375.18, but not less than 20 feet long.

Do you always need 2 ground rods?

If a single ground has a resistance of 25 ohms or less, building codes allow it to be used as the only grounding device. If the resistance of a ground rod is greater than 25 ohms, at least one additional ground rod is required.

What is the meaning of electrical work in construction?

Electrical work means: connecting or disconnecting electricity supply wiring to and from electrical equipment; or. installing, removing, adding, testing, replacing, repairing, altering or maintaining electrical equipment or an electrical installation.

What is permanent power supply?

Permanent Power means an electrical service that has been installed to provide power in or on a building, mobile home and premises.

What are the requirements for a temporary power pole in Texas?
Poles shall be set in the ground a minimum of 4 feet, solidly tamped, and project a minimum of 12 feet out of the ground. A taller pole may be required to meet NEC clearance requirements greater than 10 feet. The pole should be set so that it will not be under or within 10 feet horizontally of other lines.

What are the temporary services needed on construction site

What is building electrical installation?

Electrical installation as a verb

Physical installation of electrical wiring systems onto and within the building structure. Testing or wiring systems (usually for insulation resistance and to check for any damage). Installation of electrical equipment and its connection.

How do you repair after a fire? 8 Essential Steps to Rebuilding Your Home After a Fire
  1. Apply for a fire insurance claim.
  2. Determine the extent of damage to your home.
  3. Secure your premises.
  4. Start with structural repairs.
  5. Begin with electrical system repair.
  6. Repair fire-specific damage to the house.
  7. Restore every room, one by one.
Should a house be rewired after a fire?

After a fire, you should have your electrical wiring inspected. Any melted or damaged wiring needs to be replaced — even if the wire insulation looks just a little damaged — to ensure you won't have a secondary electrical fire on your hands. Wisconsin, Illinois, Indiana, Michigan, Minnesota, Texas and Florida.

Do you have to rebuild the same house after a fire?

While many homeowners choose to rebuild their homes after they've been destroyed, you always have the option of taking your insurance payout and buying a new house. Here's everything homeowners need to know about what to do after a fire burns down their home.

Which power source is used on a construction site?

In order to provide all the needed power at a construction site, general contractors often use large, often transportable power supplies, like generators, temporary solar panel installations and even the existing municipal power grid.

What size wire do you use for a temporary power pole?

Customer provides and installs service entrance wires, size #6 copper or #4 aluminum, minimum. A minimum of 3' of each conductor shall extend beyond the weatherhead. All wires should be same size. (NEC) 6.

How many amps should a temporary power pole be?

Maximum capacity of temporary construction poles covered by OPPD's Rate Schedule 470 is 200 amps single-phase.

What size wire do I need for a 100 amp temporary service?

#2 aluminum

Temporary services having distribution panels rated 100 amps or less, must use #2 aluminum USE or USE-2 conductors. Conductors must extend 18” beyond end of conduit.

Who carries the most responsibility on a construction site? A site manager works on construction sites and takes responsibility for a construction project. This duty involves ensuring the completion of projects to the client's specifications, on time and without going over budget.

Who is in charge of construction sites? Construction Manager

Construction managers oversee a whole project. They're responsible for the top-down view, including communication with customers, architects, and inspectors. They manage the planning and budgeting. They decide on materials and schedules, and help everyone stay coordinated.

What is the hierarchy of a construction site?

The construction site hierarchy is similar to a regular business and includes. The owner/CEO sits at the top of the organizational chart, typically followed by the general manager, department managers, project managers, project supervisors, project coordinators, and finally the workers.

  • Who is the person in charge of a construction project?
    • A construction superintendent is the individual who oversees every step of the construction process, from planning to completion.

  • What is the boss on a construction site called?
    • Superintendent

      At larger construction firms, a superintendent oversees the foremen, supervising the project between the project managers and foremen. This makes them generally in charge of directing the project during every stage—from planning to submission.

  • Is electrical before or after framing?
    • After framing, but before the drywall is installed, there will be a rough-in stage of electrical installation when access is still available to the space between the studs, floor joists, and ceiling joists.

  • Should plumbing or electricity come first?
    • For most home building projects, it's ideal for the plumbing fixtures to be installed before the electrical. During the plumbing rough-in installation, all of the water supply, drain pipes, and waste pipes are run through holes in the house's studs and framing structure.

  • What stage of construction is trim in?
    • Home Building Phase #6: Interior Trim & Flooring

      After insulation and drywall has been completed, the builder can now install the interior doors, baseboards, window sills, molding, door casings, stairs, and other decorative trim.

  • What is the order of operations when building a house?
    • This guide will show you the process of building a house, so you'll know what to expect each step of the way.
      1. Building Site Preparation.
      2. Pouring the Foundation.
      3. Framing.
      4. Setting Up Plumbing, Electrical & HVAC.
      5. Adding Insulation.
      6. Adding Drywall.
      7. Interior Finishes.
      8. Exterior Finishes.
  • Does electrical need to be done before drywall?
    • Here's a checklist of items that need to be installed before the drywall goes up: Electrical: All wiring and electrical boxes installed for wall outlets, switches, and light fixtures. Plumbing: Drain lines along with hot and cold water lines. Heating and Cooling: Any ductwork for room vents and air return.

  • What is utility project construction?
    • Utility construction is a kind of construction that focuses on what we consider modern utilities. This style of construction can focus on everything from energy transmission all the way to telecommunications.

  • What happens in a construction company?
    • It typically starts with planning, financing, and design, and continues until the asset is built and ready for use; construction also covers repairs and maintenance work, any works to expand, extend and improve the asset, and its eventual demolition, dismantling or decommissioning.

  • What is a utility in civil engineering?
    • Utilities are infrastructure services provided to consumers that are sometimes considered to be 'public' services, that is, they are supplied to the public and are important for the normal functioning of society.

  • What does a utility project engineer do?
    • A utility engineer is a civil engineer who works for a utility company, such as a water, gas, or electric company. Their job duties are to design, implement, and maintain utility infrastructures, such as water or gas mains, electrical grids, and other types of delivery systems.

Leave A Comment

Fields (*) Mark are Required